Benutzer:JosephaLeeds128
Aus Salespoint
K (Die Seite wurde neu angelegt: „Learning how to construct your own COMPUTER from scratch can be quite a very difficult task if you know nothing about pcs. However once you figure out how to do i...“) |
K (Die Seite wurde neu angelegt: „Learning how to construct your own COMPUTER from scratch can be quite a very difficult task if you know nothing about pcs. However once you figure out how to do i...“) |
Aktuelle Version vom 17:23, 15. Mai 2012
Learning how to construct your own COMPUTER from scratch can be quite a very difficult task if you know nothing about pcs. However once you figure out how to do it and also understand exactly how to handle it, it actually gets quite enjoyable to be able to easily strip down and develop old or new PC's. I would prefer to take this possiblity to lay out the essential components of some type of computer and help you learn to build a computer from scratch.
PC Components
The most typical pc components that you will need to have are the mouse, keyboard, hard drive, floppy drive, ram chips, sound and graphics card, power supply, motherboard and monitor. I'm assuming you will know what these components look like. If you are usually unsure about a few components just hunt for pictures of them online and you will see what they are generally.
Connection Process
Firstly you have to utilize the mother board plus the mother board installation plate. Firstly, gently screw the motherboard onto mom board plate using the notches or screws which were provided with the particular package or equipment. Once this is done you simply must insert the PC (Central Digesting Unit) straight into its slot around the motherboard. Sometimes these PROCESSOR sockets have levers which you need to gently release to open it up so take note of that. Gently slide the particular CPU into its socket making certain the pins for the backside slide in correctly otherwise it might get damaged. You can currently clip the lever back into place and be sure it is safe.
Now you must attach the heatsink towards the CPU chip. You might find that the CPU already incorporates the heatsink/fan attached with it then you can read additional. Now you should connect small cable from the actual heatsink fan for the corresponding socket around the motherboard to supply it power.
The next step is to place the ram chips within their respective slots that happen to be long and thin. Once this has been done you may well mount the motherboard growing plate onto the inside of the computer and screw/slip it in in order that it is attached properly.
The power supply is the next component to handle. The power supply area is usually located at the rear of the pc case and is also indicated with screw holes which are unoccupied. Just try and also maneuver it around to match with the corresponding holes when you screw it within. The power supply carries a main system connection which gets plugged into the power slot around the motherboard, a floppy power connector which gets attached to the floppy drive or a few standard peripheral energy connectors (reddish, yellow and black wires) which get connected to your hard pushes and cd roms. You will have to mount the hard disks, cd roms and floppy drives and connect them with those connectors making sure that the red wire on each energy connector is pointed inwards towards the motherboard. I'll explain why below.
Right, now we move onto both the ports on the motherboard called the key and secondary IDE Slots. You will notice them because they are rectangular with brackets around these. these ports are employed to connect the hard disks and cd roms. The cables that get plugged into these two locations are 40 flag IDE cables with have 3 contacts on each cable tv. Make sure the longest the main cable is connected to the IDE locations. You need to plug the primary IDE cable from your motherboard to the particular hard drive(s) plus the secondary IDE port is employed to connect the DVD Roms for a motherboard. When you put these IDE cables to the cdroms and hard drives be sure that the red wire strip is hand and hand with the red-colored wire strip with the power connectors that are connected to those people devices. Consult your manual if you have one to find out how to use the different jumpers to modify between master and salve drives about each port. This will enable you to choose which pushes are primary along with secondary.
Now that the ability supply is linked to the motherboard and the various other components you will have to plug graphics as well as sound card to their slots. Once this is done make sure you connect the top panel connectors to the corresponding LED lights which means your lights will appear when the pc boots. Failure to do so can lead to non function of the system.
Lastly make certain everything is linked properly. This includes the external mouse, keyboard, monitor cable and also power cables in order that the computer will first turn on and function appropriately. If all is done well then it must be okay.pc